Level 3 Inspection, Author at Level 3 Inspection - Page 13 of 13

Author Archive

Wax or Epoxy Patterns

Wax or Epoxy Patterns

After the tool is complete a quick check method of inspecting the cavity without having to inspect the actual is to SmartComapre a wax or epoxy pattern although there will be some shrink and shape change this method can be used to quickly quantify any gross deviations from the CAD model. By inspecting the wax or epoxy patterns for correctness prior to casting parts, any issues can be found and resolved quickly and cost effectively. Level 3 Inspection can use White Light Scanning (WLS) with computer-aided-inspection (CAI) to compare the Wax or Epoxy Pattern to the CAD model, other Wax or Epoxy Pattern and wax/epoxies of the same die taken over a period of time, to trend wear. This technology gives our customers a new and profound insight into the size shape and geometric conformance of Wax or Epoxy Pattern that they have never had before. By inspecting and perfecting the actual Wax or Epoxy Pattern Level 3 can help their customers quantify shrink rates, identify problem areas in the die and bring better castings to market, faster than ever before.

Level 3 Inspection’s SmartComapre process gives their customers the ability to identify problems with a particular area of the part and focus efforts to improve problem areas without spending time and resources on areas that are known to be conforming. This is especially helpful when dealing with middle step products, such as Wax or Epoxy Pattern. The ability to quickly compare a representative of the cavity shape to the nominal CAD model as well as the ability to compare multiple molds and multiple scans of the same mold over time gives Level 3 Inspection’s customers an advantage in regard to quality and time to market.

CMM captures only a few points in the time that WLS can capture hundreds of thousands, so Level 3 is able to do a more thorough inspection. The results are much more visual and therefore much more easily understood and interpreted.
Inspecting injection molded products with complex free form geometry poses some unique challenges, such as analyzing the complex surface areas. This is difficult using a CMM system, which depends on the operator to accurately capture the points that will show whether or not the part is conforming within the allowable tolerance. Often, there is not enough point data to make an accurate comparison.
The new capabilities provided by computer-aided inspection have not come a moment too soon for the increasingly competitive injection molding and ceramic core market. Increasingly, companies are facing the demand for more quality inspection results in less time.
Level 3 Inspection’s customers are moving quickly to statistically based inspections in which the qualification is based not on a single piece, but on a sampling of parts, new part inspection would take much longer to complete without the ability to automate portions of the process.

Traditionally, studies based on a sampling of parts are done using CMM to generate metrics on dimensions for each part. This is a time-consuming process, since each part must be measured individually. Data is then typically transferred to an analytic program, evaluated, then published.

Level 3 is replacing the CMM-based process with automated trend analysis. Once a part is scanned and a report is saved, Level 3 can automatically generate portions of the capability studies defined by their customer or OEM specifications. Batch processing enables Level 3 to collect data and generate reports on a large number of parts. Statistical analysis tools allow Level 3 to compare parts for pre-defined factors such as repeatability, changes over time, and variations from part to part.
Speed is the key. Speed of inspection is always Level 3 Inspection’s main challenge. Everyone wants the results yesterday and our process is helping us deliver more complete results much quicker.
Contact us today to start getting superior inspection results in shorter time with easier understanding leading to higher confidence.

Press Release – Automation Designer-Create New Inspections in Minutes

New Automation Designer in Geomagic Qualify 11 enables users to create new inspections in minutes
Innovative V11 features “set new standard for ease of use and productivity”
RESEARCH TRIANGLE PARK, N.C., April 29, 2009 – Geomagic announces Geomagic Qualify 11, the latest version of its computer-aided inspection (CAI) software with a new Automation Designer that dramatically reduces the time it takes to create new inspections. Geomagic Qualify 11 will begin shipping on May 4 and is making its public debut next week in the Geomagic booth at Control 2009 in Stuttgart, Germany.
“The most demanding inspections can be designed and automated within minutes using Automation Designer, thanks to its drag-and-drop visual interface,” says John Lockhart, Geomagic Qualify product manager. “There’s no need for macros or any special programming. When something changes in your inspection workflow, be it the reference model or additional analysis that you want to perform, you can easily edit the process you have already designed.”
Easily migrate and test different inspection processes
Using the new Migrate Automation Wizard, existing inspection processes can be easily transferred between reference models for re-use when part designs change. Users simply load the new part and transfer their inspection steps, then Migrate Automation Wizard guides them in resolving areas of the inspection process that need further attention.
Geomagic Qualify 11 also includes options for constructing new features that enable users to simulate tab and slot alignment and define midpoints. With version 11, Geomagic Qualify and Studio are built from the same core technology, ensuring consistency among shared functions and file compatibility between the two applications.
Setting a new standard
“Geomagic Qualify 11 sets a new standard for ease-of-use and productivity in high-precision manufacturing inspection and design analysis,” says Scott McAfee, vice president of engineering at Level 3 Inspection, a leading provider of CAI services and systems for the aerospace industry. “The new automation features will save us time and enable us to quickly adapt inspection routines to new parts and applications, allowing us to deliver higher value to our clientele.”
Available in multiple languages
Geomagic Qualify 11 ships with both 32- and 64-bit editions on the CD, and supports English, German, French, Italian, Spanish, Chinese and Japanese languages. Customers with active maintenance can download the Qualify 11 upgrade from Geomagic’s portal:
https://portal.geomagic.com.
About Geomagic Qualify
Geomagic Qualify takes advantage of digital shape sampling and processing (DSSP) to enable fast, easy-to-understand graphical comparisons between CAD models and as-built parts. It is used worldwide to save time and increase accuracy for first-article inspection, inline or shop-floor inspection, MRO, trend analysis, 2D and 3D dimensioning, and automated reporting. Geomagic Qualify is certified by PTB, ANFIA, and major customers such as Honeywell, Fiat, General Motors and Pratt & Whitney.
About Geomagic
Geomagic (www.geomagic.com) simplifies digital shape sampling and processing (DSSP) for more than 8,000 professionals in industries such as automotive, aerospace, medical devices and consumer products. The company’s products and services are used to enable mass customization with the same efficiency and cost as mass production, improve dental care with individually designed devices, speed time to market for consumer products, automate inspection for better quality in dramatically less time, increase safety for NASA shuttle missions, and optimize design for everything from racing cars to blimps. Geomagic has headquarters in Research Triangle Park, N.C., subsidiaries in Europe and Asia, and distributors worldwide.

Wax Dies

Wax Dies

In a product life cycle the largest investment is always the tooling, this is especially true in investment casting. Until now the actual geometry of the wax die has been largely unknown. Level 3 Inspection can use White Light Scanning (WLS) with computer-aided-inspection (CAI) to compare the wax die to the CAD model, other wax dies and scans of the same die taken over a period of time, to trend wear. This technology gives our customers a new and profound insight into the size shape and geometric conformance of wax dies that they have never had before. By inspecting and perfecting the actual wax die Level 3 can help their customers quantify shrink rates, identify problem areas in the die and bring better castings to market, faster than ever before.

Level 3 Inspection’s SmartCompare process gives their customers the ability to identify problems with a particular area of the part and focus efforts to improve problem areas without spending time and resources on areas that are known to be conforming. This is especially helpful when dealing with middle step products, such as wax dies. The ability to quickly compare the product mold to the nominal CAD model as well as the ability to compare multiple molds and multiple scans of the same mold over time gives Level 3 Inspection’s customers an advantage in regard to quality and time to market.

CMM captures only a few points in the time that WLS can capture hundreds of thousands, so Level 3 is able to do a more thorough inspection. The results are much more visual and therefore much more easily understood and interpreted.
Inspecting injection molded products with complex free form geometry poses some unique challenges and is difficult using a CMM system, which depends on points that to show whether or not the part is conforming within the allowable tolerance. Often, there is not enough point data to make an accurate comparison.
Level 3 Inspection’s customers are moving quickly to statistically based inspections in which the qualification is based not on a single piece, but on a sampling of parts, new part inspection would take much longer to complete without the ability to automate portions of the process.
Traditionally, studies based on a sampling of parts are done using CMM to generate metrics on dimensions for each part. This is a time-consuming process, since each part must be measured individually. Data is then typically transferred to an analytic program, evaluated, then published.

Level 3 is replacing the CMM-based process with automated trend analysis. Once a part is scanned and a report is saved, Level 3 can automatically generate portions of the capability studies defined by their customer or OEM specifications. Batch processing enables Level 3 to collect data and generate reports on a large number of parts. Statistical analysis tools allow Level 3 to compare parts for pre-defined factors such as repeatability, changes over time, and variations from part to part.

Speed is the key. Speed of inspection is always Level 3 Inspection’s main challenge. Everyone wants the results yesterday and our process is helping us deliver more complete results much quicker.
Contact us today to start getting superior inspection results in shorter time with easier understanding leading to higher confidence.

What is White Light Interferometry Scanning (WLS)?

White Light Interferometry Scanning (WLS)

While white light interferometry is certainly not new, in fact the development of scanning white-light interferometry is in many ways a back-to-basics scenario. As interferometry progressed from using white light to monochromatic light to lasers to computerized fringe analysis to phase shifting techniques, the path has actually led right back to white light. Scanning white-light interferometry combines the power of modern high-speed computers with the vast amount of surface information produced by white-light interferometry. This permits WLS-based systems to measure surface features far more accurately than those measurable with conventional phase-measuring interferometry techniques.
White-light interferometry scanning (WLS) systems capture intensity data at a series of positions along the vertical axis, determining where the surface is located by using the shape of the white-light interferogram. The white light interferogram actually consists of the superposition of fringes generated by multiple wavelengths, obtaining peak fringe contrast as a function of scan position, that is, the red portion of the object beam interferes with the red portion of the reference beam, the blue interferes with the blue, and so forth. In other words, a prodigious amount of data is available in white-light interferograms.
Conventional WLS systems use fringe contrast to yield surface information. Frequency domain analysis (FDA) is an alternate approach that uses all of the information available in the interferogram. This Fourier analysis method is used to convert intensity data to the spatial frequency domain, allowing production of an extremely accurate surface map.
In a WLS system, an imaging interferometer is vertically scanned to vary the optical path difference. During this process, a series of interference patterns are formed at each pixel in the instrument field of view. This results in an interference function, with interference varying as a function of optical path difference. The data are stored digitally and Fourier-transformed into frequency space.
At this point the original intensity data are expressed in terms of interference phase as a function of wavenumber. Wavenumber k is just a representation of wavelength in the spatial frequency domain, defined by k = 2p/l. If phase is plotted versus wavenumber, the slope of the function corresponds to the relative change in group-velocity optical path difference DG by Dh = DG/2nG where nG is group-velocity index of refraction. If this calculation is performed for each pixel, a three-dimensional surface height map emerges from the data.
In the actual measuring process, the optical path difference is steadily increased by scanning the objective vertically using a precision piezoelectric positioner. Interference data are captured at each step in the scan. In effect, an interferogram is captured as a function of vertical position for each pixel in the detector array. To sift through the large amount of data acquired over long scans, a patented technique involving both acquisition and processing algorithms is used. This method allows the instrument to reject raw data that do not exhibit the intensity variations that indicate white-light fringes.
Using discrete Fourier-transform techniques, the intensity data as a function of the optical path difference are converted to the spatial frequency domain.

Six Sigma and CAI

Computer-Aided Inspection (CAI):

Six Sigma is a highly disciplined process that focuses on developing and delivering near-perfect products and services. Sigma is a statistical term that measures how far a given process deviates from perfection. The central idea behind Six Sigma is that if you can measure how many defects you have in a process, you can systematically figure out how to eliminate them and get as close to zero defects as possible. Manufacturing companies around the world are implementing the Six Sigma process to:
  • Improve customer satisfaction
  • Maximize process efficiencies
  • Increase competitive advantage and market share
  • Save millions of dollars in operating expenses
Jack Welch, former CEO of GE, says that Six Sigma is “the most important initiative GE has ever taken…it is part of the genetic code of our future leadership.”
Many companies implementing Six Sigma use a process called DMAIC (define, measure, analyze, improve and control) for continued improvement. DMAIC is a systematic, scientific and fact-based process that eliminates unproductive steps. It helps companies fulfill the vision of Six Sigma.
New computer-aided inspection (CAI) technologies can drastically improve the “measure” and “analyze” part of the DMAIC process, making them valuable tools in the Six Sigma approach to quality.

The Bottleneck

It is well documented that three-dimensional verification is frequently the slowest, most expensive and disruptive element of the manufacturing process. Advances in CAD/CAM/CAE and digital technologies continue to improve other manufacturing processes, but the dimensional inspection bottleneck has remained intact.
Manufacturing companies spend a significant percentage of their resources to develop 3D CAD models that define the design of a part. But, the efficiencies of the 3D CAD model do not carry over into the verification and inspection processes.
Designers break the 3D models into 2D drawings and apply constraints to determine product configuration. Geometric design and tolerance (GD&T) assigned in 2D drawings are then evaluated in the 3D models, yielding a complex web of dependencies. Changing and maintaining the 2D drawings requires considerable effort, and the process contains a great deal of duplication.

Today’s Inspection Process

Most inspection today is done by contact metrology, the science of physically determining an object’s dimensions. Contact metrology includes everything from simple manual tools to coordinate measurement machines (CMM).
A CMM system consists of a platform on which the desired measurement object is fixed. The station has an arm where a touch probe is attached. The machine makes direct contact with the object being measured at a rate of approximately one contact measure per second. CMM systems vary in size depending on the objects they need to measure. They are slow, large, expensive and susceptible to environmental temperature variation.

The CAI Alternative

CAI aims to remove the bottleneck of dimensioning verification in the manufacturing process. It is not intended to replace metrology, but rather to introduce a faster and easier process for directly comparing as-built parts with their 3D CAD definition.
There are two widely used non-contact measurement systems for CAI: 3D scanners and laser trackers. 3D scanners are commonly used for range finding. They work by projecting a laser beam onto an object and measuring its reflected image with a positioning sensor. 3D scanners are fast and can be mounted onto an existing CMM.
White Light Scanning is also known as interferometry. By knowing the wavelength of the emitted light and the distance between fringes, the distance between two points can be computed.
Non-contact white light measurement systems collect data much faster than CMM’s. It is common to collect tens of thousands of points per second. With massive amounts of data being transmitted to a computer for processing, software based on complex mathematics and sophisticated algorithms must be used to interpolate the data quickly.

The CAI Wish List

The new wave of CAI systems combine fast, non-contact measurement machines with software that aligns, compares, evaluates and reports the deviation between as-built parts and the 3D CAD reference model. Market research has determined that customers want the following attributes in a CAI solution:
  • Accuracy of 0.001mm to 0.005mm
  • Speed of more than 10,000 points per second
  • Portability for in-process measurement
  • An open system for rapid conversion to standard or native CAD formats
  • Automatic align, compare, evaluate and report process
  • Repeatable setup, process and results
  • Ease of use so it can be deployed on the shop floor by inspectors with no CAD training
  • Go/no-go displays that enable an automatic pass/fail check with pre-defined tolerances

Fulfilling the CAI Promise

CAI software will become a mainstream application and an essential part of the digital product development cycle. Pushing quality inspection into earlier phases of the development cycle will speed product development and ensure greater quality. As supplier networks continue to expand and products are increasingly differentiated according to quality, how well a company implements the inspection process can be a make or break factor in the marketplace.
CAI is beginning the same way as most new technologies. The innovators are relatively small companies without extensive marketing resources to penetrate deeper into large manufacturing operations. System integrators and consultants are needed to customize the new CAI technologies and integrate them into existing digital manufacturing processes.
CAI can eliminate the requirement for generating 2D drawings for parts and tools, which can save hundreds of engineering hours. It places the verification and inspection process into the 3D digital realm, where it can be fully integrated into existing CAD/CAM/CAE processes. This will allow manufacturers to reap greater benefits from their CAD/CAM/CAE investments and bring them closer to the promise Six Sigma.
The biggest obstacle to CAI acceptance is the inertia caused by familiar ways of doing things. Unwillingness to take a risk is always a deterrent to innovation. But, the difference between CAI and earlier digital processes is that there is much less risk. CAI technologies complement, rather than replace, the CAD/CAM/CAE systems manufacturers already have in place. Early adopters of CAI will get a head start in establishing processes whose benefits will only multiply with time.

Press Release – ISO9001-AS100 Certifications

Press Release
Level 3 Inspection Achieves 100% Compliance In ISO 9001 & AS 9100 Certification
Jupiter, FL, USA — January 28, 2009 — Level 3 Inspection LLC (L3I) is proud to announce that it has successfully completed the Quality Management System (QMS) development by meeting or exceeding all of the requirements for ISO 9001:2000 and AS9100 Certification under the rules of the aerospace standard. L3I passed their ISO/AS audit with 100% compliance and zero non-compliance issues.
Starting in May of 2008, Vice President of Operations, Scott McAfee led the creation, organization and refinement of the comprehensive QMS documentation for procedures and processes that covered the entire L3I business. McAfee elected to create the company’s QMS system completely online, for universal access to support, ease of editing and use, with proper login security.
In October, the company met their auditor to review the completeness, correctness, and compliance of the original QMS documentation system. After several weeks of work, including with an ISO and AS conformance consultant, L3I’s management team, led by McAfee, finished the rest of the tasks and held their annual management meeting to review both the QMS system and the actual documented results from implemented procedures.
In late December 2008, the final audit was performed over the course of the two-day comprehensive evaluation. The company, its QMS system, and it’s implementation/usage of the system, all received the 100% compliance rating.
“This world-class international quality standard was important for our immediate business expansion plans,” said Bill Greene, Vice President of Business Development. “There are some prospects and clients in the aerospace industry that require the ISO certification in order to qualify to engage in business. We wanted to exceed that standard and get our AS certification while we were at it, since this market is so properly conscientious.” continued Mr. Greene.
Once issued by the audit review committee, L3I’s certificates will be posted on their web site, www.level3inspection.com along with the compliment of their other qualifications and certifications for excellence in performing their dimensional and geometric inspection services business. Further background on the company, its professional technical services, and it’s leadership role in the field of White Light Scanning (WLS) and Computer Aided Inspection (CAI) are also available on the company’s web site or by calling 888-4AS-9102 x102.
Contact:
Bill Greene
Founder, Vice President Business Development
Level 3 Inspection LLC
E: bill@level3inspection.com
T: 561.775.7911

White Light Advantages

Transform your legacy tooling into parametric CAD models
Build an electronic, easy to use, database of FAI and Periodic layout results for FAA and customer compliance
Evaluate non-conformances faster and with more confidence than ever before
information@level3inspection.com
www.level3inspection.com

Quality Inspection and Beyond

Level 3 Inspection is the only source for AS9102 compliant inspections using advanced white light scanning-
AS9102 Compliant First Article and Periodic Layout Inspections
CMM equivalent white light production inspection with improved results and exceptional visualization
Decades of OEM Aerospace design, inspection and manufacturing experience focused on turbine blades and vanes
Full service dimensional layout inspection and reporting using a variety of inspection methods focused on white light scanning and computer aided inspection
Casting, forging, machined and formed parts inspected to +/- .0002 (.005mm) accuracy
For more information contact us:
sales@level3inspection.com
www.level3inspection.com
MENU