Updates & News - Page 5 of 14 - Level 3 Inspection

OMTEC 2012 SmartInspectionStation™ Demo and “Choose All Three” Presentation

Meet us at OMTEC, Booth #831-833, June 13-14, 2012
Register to attend.
Presented by:
Bill Greene
Chief Executive Officer
Level 3 Inspection LLC

Price, Quality, Speed: Choose All Three

Thursday, June 14, 2012, 10:00 a.m. – 10:45 a.m.
Orthopaedic Manufacturing & Technology Exposition & Conference
Donald E. Stephens Convention Center, Rosemont, Illinois

Participants will learn about the advantages of Computer Aided Inspection for orthopaedic devices:

  • Make better parts faster, with fewer iterations, greater confidence and lower cost
  • SPC tracking and trending of dimensions to reduce sampling rates
  • Trim 30% from new product time-to-market (TTM), saving millions of dollars
  • Reduce legal exposure by avoiding expensive product performance liability problems

Witness the Power of the SmartInspectionSystem™!

The SiS™ is an easy-to-use fully-automated Structured Light Metrology (SLM) and Computer Aided Inspection (CAI) system that orthopaedic and other precision manufacturers can install practically anywhere in their operations.

This patent-pending system uses SLM in tandem with a programmable part positioner and Geomagic Qualify™ to digitize the surfaces of orthopaedic implants and other precision manufactured parts, automatically generating full PDF inspection reports in mere minutes, with minimal operator input and personnel training.

The SiS™ is highly configurable, offering scanning resolutions of 4, 5, and 11 (or more) megapixels, with measuring volumes ranging from 50-380mm (or bigger) to generate very high scan data density as needed per part, feature, and tolerance.

Come and see the SiS™ in operation at OMTEC Booth #831-833, June 13-14, 2012.

Register to attend.

Copyright © 2012 Level 3 Inspection LLC, All rights reserved.

The Future of Inspection, Part 4: Trackable

Integrating 21st century metrology into FDA-mandated quality systems provides many benefits.  Here are just a few…
In this email series, we’ve discussed the archiveability, auditability, and traceability of Computer Aided Inspection (CAI) data for reference and accountability. We now add trackability to CAI’s list of superlatives.

Failure analysis is a tricky business. As a rule, systematic investigation is more effective and far less expensive than haphazard trial and error. The faster and more accurately manufacturers gather information, the faster and more accurately they can find root causes and understand the limits of their process capabilities – saving time and money.

Vast quantities of trackable data, available only through CAI, enable intelligent deductive analysis, providing quick and effective tracking from why-gate through why-gate. There is no longer any need (or excuse) for expensive, repetitive iterations.

Once data have been tracked and root causes found, process capability can be enhanced through specific production measurement plans. Visit www.level3inspection.com or call us today to discuss the ways in which an in-house, traceable CAI system can suit your needs.

WARSAW, IN • STUART, FL
574.383.9145 • 561.775.7911
Copyright © 2012 Level 3 Inspection LLC, All rights reserved.

The Future of Inspection, Part 3: Archiveable

Integrating 21st century metrology into FDA-mandated quality systems provides many benefits.  Here are just a few…
Along with tamper-resistance, Structured Light Metrology (SLM)-based data are highly traceable.  When every step in manufacturing can be linked to a comprehensive dimensional inspection process, metrology loses its anonymity.

In this series, we’ve already discussed the archiveability and auditability of Computer Aided Inspection (CAI) -based inspection.  Gauge R&R studies demonstrate that CAI incorporates minimal operator-dependent error.

Modern CAI practices allow manufacturers to trace measurements to a precise date, time, and employee.  This results in a new level of accountability for engineering data.

Even better, CAI makes it possible to trace failures to their root causes quickly and effectively.  When manufacturers are able to find the cause of process failures quickly, they can alter their processes equally quickly – saving time and money.

Visit www.level3inspection.com or call us today to discuss the ways in which an in-house, traceable CAI system can suit your needs.

WARSAW, IN • STUART, FL
574.383.9145 • 561.775.7911
Copyright © 2012 Level 3 Inspection LLC, All rights reserved.

The Future of Inspection, Part 2: Auditable

Integrating 21st century metrology into FDA-mandated quality systems provides many benefits.  Here are just a few…
Correct information technology practice and data validation are key to avoiding minor headaches during your self-audits … or living nightmares when FDA inspectors knock on your door.

Computer Aided Inspection (CAI) tools save comprehensive surface data, instantly.  Every Structured Light Metrolgy (SLM) scan clearly and precisely demonstrates a part’s (or thousands of parts’) dimensions at a given process stage.

By using checksums and digital signatures, you can make your CAI data immune from tampering.  Manufacturers are discovering that by securing CAI data into a database that cannot be changed once logged, they can have incontrovertible evidence of a watertight quality system.

For the first time, thanks to CAI, you can prove that every surface point of your product was within spec at every point during manufacturing, allowing you to quickly and incontrovertibly dispatch regulators’ questions.

Visit www.level3inspection.com or call us today to discuss how an in-house, archiving CAI system can suit your needs.

WARSAW, IN • STUART, FL
574.383.9145 • 561.775.7911
Copyright © 2012 Level 3 Inspection LLC, All rights reserved.

Quality, Speed, Price: Pick Three

Read L3I’s latest BONEZONE article:
“Quality, Speed, Price: Pick Three”
We’ve done it again.

L3I’s CEO Bill Greene was featured in December 2011’s BONEZONE, a major orthopedic trade journal.  This time, Mr. Greene explains how modern, 21st century best dimensional inspection practices can help U.S.-based medical device manufacturers remain globally competitive.
A few excerpts:
“Engineering misjudgments of mere microns can necessitate an expensive recall. Modern computer aided inspection and analysis software can instantly ascertain geometric surface information, discern trends and catch new problems as they arise — before they begin to cost time and money.”
“By removing human interference, the SiS can create part scan files in as little as three minutes … Even if 100% inspection is required because of regulatory considerations, robotic part handling makes it practical. Quite soon, those costly inspection cells filled with dozens of workers … will be a memory.”

“An orthopaedic product revision had endured 18 successive process iterations, aided and abetted by an inspection team using optical comparators, CMMs and fixed gauges. We finished the product revision in only two iterations. If you’re doing the math, that’s better than an 85% reduction in cycles, and weeks. It’s time to relegate wasteful iterations to the ash heap of history.”

“Accurate and comprehensive geometric data allow engineers to diagnose and solve problems that might have vexed them for years. At least as important is the opportunity to incrementally streamline production based on real-time insights, which can then be driven back into the process to create a cost-effective production measurement plan.”

Read the full text of Mr. Greene’s paper here.
Avail yourself of fast, modern, and economical Computer Aided Inspection (CAI) by a credentialed, independent and impartial third party.  Level 3 Inspection is an ISO 9000, AS 9100 and AAAM 44.9 certified engineering and inspection firm, and is among the world’s most competent practitioners of Structured Light Metrology (SLM)-based CAI.
Visit www.level3inspection.com or call us today to discuss the best inspection solution for your device design or manufacturing needs.
WARSAW, IN • STUART, FL
574.383.9145 • 561.775.7911
SERVICES • SYSTEMS • SOLUTIONS
Copyright © 2012 Level 3 Inspection LLC, All rights reserved.

Holiday Greetings from Level 3 Inspection

Season’s Greetings from L3I

What’s on your wish list?

We at Level 3 Inspection deeply value our partners (and prospective partners) in medical devices and other close-tolerance precision manufacturing.

We’re curious about what your industry would most like to see from a leading U.S.-based metrology provider in 2012.

Click the image below to fill out your Holiday Wish List, which requires less than one minute to complete.

If the image doesn't load, please visit https://docs.google.com/spreadsheet/embeddedform?formkey=dDZTUmxVRGNmZFFvSlh5bjl2RTNPQlE6MQ fill out your Holiday Wish List.

Wishing you happy holidays and a prosperous new year!

Copyright © 2011 Level 3 Inspection LLC, All rights reserved.

Blocker Door Inspection

Level 3 Inspection Serves AAR PMA Group
Through the Complete Product Modernization Cycle
Advanced technologies and new process capabilities in expert services support market demands for improved replacement parts in the jet engine industry.
Companies who are engaged in commercial aviation replacement parts production under FAA Parts Manufacturer Approval (PMA) often need to capture and reproduce complex part geometry with higher accuracy and even tighter tolerances than the original manufactured part.
For some suppliers, these strict requirements can be insurmountable. For PMA companies such as AAR, the ability to meet these requirements with technical services support from Level 3 Inspection, has become a comparative advantage that leads to expanded business. This Article illustrates an unusual “full circle” approach from reverse engineering through first article inspection and into production with production sampling inspection.
AAR, founded in 1951, is a worldwide aviation support company offering services that include MRO, supply chain, structures and systems, and sales and leasing. Their product development center is in greater Atlanta and they employ many design engineers who use traditional measurement technologies and current CAD programs to produce the parts their airline customer’s demand.
Level 3 Inspection combines a depth of aerospace expertise with state-of-the-art 3D White Light Scanning (WLS) and advanced geometric processing technologies to reverse engineer, quality inspect, design optimize and then validate turbine engine components and assemblies.
AAR originally worked with the technical professionals who founded Level 3 Inspection (“L3I”) www.level3inspection.com to reverse engineer a complex jet engine thrust reverser part without any existing CAD data.  After the new CAD models were created from OEM part scans, and the investment casting process optimized to produce the first parts, AAR also requested the First Article Inspection of the new produced parts to be performed by L3I. Production inspection is anticipated to happen as soon as the first lot of new PMA parts is available.

Beyond CMM and CAD

AAR provided L3I with five sample OEM-produced parts that needed to be accurately 3D digitized then averaged into a nominal CAD model.  In the past, AAR would have used their own touch-point CMM to gather the data and then build the model in CAD software from averaged data.  This particular part, however, was a blocker door for a turbine engine made up of complex, organic shapes.  The part would have been difficult or impossible to capture and recreate using a CMM point-data and CAD software.
The geometry for the part was very challenging,” said Paul Ilenda, Manager of Outside Engineering Services for AAR’s PMA Group.  “There were no flat surfaces and seemingly many irregularities from part to part.”
Level 3 Inspection was uniquely qualified to do the work because of its expertise in aerospace parts digitizing using a White Light Scanner for data capture and then comprehensive post-processing of the scan files with software for aligning, averaging and modeling the large data sets generated by the scanner.  3D WLS is particularly suited to MRO projects because it enables engineers to quickly capture and process the average or optimal shape with tremendous accuracy, within 0.0005 inches (13 microns).
Using automated features in post processing software, Level 3 Inspection created a new average dataset From multiple 3D scans of the five AAR sample parts.
“The ability to create an average data set automatically saved a large amount of time and eliminates the guess work of manual averaging,” says Scott McAfee, Level 3 Inspection’s Vice President of Engineering.  “It provides a complete visualized data set rather than just specific dimensions.  This aids tremendously in the highly iterative CAD model-development process.”
McAfee took the sections taken from the average model and imported them into CAD/CAM software to create the nominal model.  From the nominal model, a detailed dimensional report, including GD&T, was created in their software.  The software then was used to batch-process report results from the original five data sets.

New capabilities and credibility

The final steps for Level 3 Inspection were converting the optimized CAD model to CATIA, and delivering the supporting dimensional package to AAR.  The entire process of digitally reconstructing the complex part, averaging the data for the samples and providing trend reports, took about two weeks.  McAfee estimates that Level 3 inspection’s ability to automate saved about a week of time or 33%.
Level 3 Inspection used software to compare the CAD model  to each of the scanned sample parts provided by AAR.
Perhaps even more important than time savings for AAR were the new capabilities that L3I brought to the table and the fact that the outsourcing freed AAR to concentrate on other projects.
“It was difficult for us to understand the intended surface geometry given the limited data from our touch-point CMM,” says AAR’s Ilenda.  “Level 3 Inspection was able to use the combination of the White Light Scanner and post processing software to provide much more comprehensive detail.  A big additional benefit was that we freed up resources internally to work on other projects while L3I was performing the reverse engineering.”
Ilenda says that the ability to tap into part digitization capabilities through Level 3 Inspection will help AAR create a greater competitive advantage in the MRO market.
“Because this was a difficult part to reverse engineer, it adds credibility to our PMA team and sets us apart from companies unwilling to take on such challenges,” says Ilenda.  “We are also able to provide a quality part to our customers at substantial savings over OEMs.”

Automation saves time and tedium

Once data was collected for the five samples, it was aligned in the post processing software.
Level 3 Inspection used software to align data sets from five AAR sample parts digitized with a 3D White Light Scanner.
Level 3 positioned the multiple scans into alignment, as the color plots graphically show any alignment problems for each scan, making it simple to identify alignment and/or part geometry deviations.
Sections from the average model were used to develop the nominal CAD model
Level 3 Inspection used software to compare the CAD model to the average data set created from each of the scanned sample parts provided by AAR.
“The ability to batch-process the reports on the five individual parts using the average report as a template was tremendously efficient,” says McAfee.  “It enabled us to compare trends from the five individual OEM parts to the average data set, which added credibility and supported AAR with plenty of information to use directly for PMA approval.”
Computer Aided Inspection Closes the Loop
Several months after their Blocker Door part was produced in the investment casting manufacturing process, AAR again called on Level 3 Inspection to perform the First Article Inspection. This critical step in part production and PMA approval was necessary to confirm that the multiple manufacturing steps were optimized to consistently produce quality parts for use in aircraft.
Level 3 Inspection used software to compare the CAD model  to the first article sample in order to report dimensional information based on the part drawing requirements (CAD model is RED – WLS data is BLACK).
All of these detailed inspections and the positive results that were the inspection outcome from this FAI process gave AAR even greater confidence in the CAD model and the production process. Based on all of the top quality outcomes and consistent geometric conformance, production runs are now being ordered from the investment casting foundries.
Most recently, AAR asked L3I to provide a proposal for production inspection on some to be agreed statistical sampling basis of the hundreds of parts contracted to be produced over the coming months. Based on the observed degree of part consistency identified in the first lot, the part sampling rate for inspection may be reduced over subsequent lots of production parts.
Updates to this unusually complete, ‘full development cycle’ of reverse engineering through first article inspection through production inspection in the PMA marketplace will be made available through this publication and on L3I’s web site, www.level3inspection.com.
By performing another comprehensive 3D digitization, using the same White Light Scanning of the new produced part, and within the separate post processing software suite, comparing it to the previously produced CAD model, L3I was able to identify the casting process results accuracy and quality conformance.
Level 3 Inspection used software to compare the CAD model  to the first article sample in order to report surface deviations.
The ability to completely and accurately scan the part and make the digital comparison between scan file and CAD model, with the level of detail and dimensional tolerances built into the Computer Aided Inspection process makes this the ideal method for proving out the manufacturing process. Additionally, L3I was asked to make a comparison of the new produced part to the OEM parts for further proof and support in the PMA process. This PMA part to OEM part comparison was critical in the acceptance and approval process.
For further information about this particular application of modern manufacturing and quality engineering technologies or any other interest applying these services and tools to solve industrial and business problems, contact Level 3 Inspection at 888-4AS-9102 or sales@level3inspection.com

The Future of Inspection, Part 1: Secure and Archiveable

Integrating 21st century metrology into FDA-mandated quality systems provides many benefits.  Here are just a few…
Secure and verifiable data archiving, for years the standard in aerospace inspection, is now under increasing demand for medical devices.

Medical device manufacturers face a number of inspection challenges – some common to all precision manufacturers, others unique to their industry.  Among these challenges are evolving design parameters and manufacturing methods, a deficiency in legacy part knowledge, and ever-stricter archiving standards imposed by many national regulatory agencies.

The truth is that today’s manufacturers should be archiving all inspection data.  Equally true is that design changes in the medical device industry remain too slow and far too expensive.  Faster innovation, faster product development, and faster manufacturing process optimization are keys to success in the increasingly demanding and competitive industry.  Manufacturers need legacy part information for reference in designing current/future product lines – to say nothing of reverse engineering legacy parts to make them better while using modern computer-aided technologies for production.  And with the glut of lawsuits and regulatory inquiries, manufacturers need to arm themselves with greater information resources and faster, easier access to their own dimensional, quality, and other manufacturing data.

Traditional inspection methods don’t solve any of these problems.  CMM’s don’t archive data automatically (if at all), at best churning out an unverifiable table of numbers.  Optical comparators and fixed gauges don’t output data, but instead rely on the non-reproducible eyes of inconsistent shop floor employees.  Fortunately, modern technological solutions now exist that automatically and verifiably collect, analyze, report, disposition and archive all dimensional manufacturing process and resulting product information as decisionable data, for a myriad of uses.

Such data can be made demonstrably tamper-proof for defense against litigation and in regulatory requests for information, via checksums and digital signatures.  Manufacturers can review past process and part data for quick and efficient reference, trending, SPC, CAD model creation, and many other applications.  Best of all, self-contained integrated and automated Computer Aided Inspection (CAI) systems can be installed in manufacturers’ facilities, minimizing turnaround time, reducing iterations, and eliminating inspection delays.

Visit www.level3inspection.com or call us today to discuss how an in-house, archiving CAI system can suit your needs.

WARSAW, IN • STUART, FL
574.383.9145 • 561.775.7911
Copyright © 2011 Level 3 Inspection LLC, All rights reserved.

Computer Aided Inspection: The Future of GMP

Integrating 21st century metrology into FDA-mandated quality systems provides many benefits.  Here are just a few…

In our three years serving the medical device industry, we at L3I have closely studied the FDA’s exacting Good Manufacturing Practice (GMP) and quality system requirements in light of our many prior years of experience serving the aerospace industry.  Aerospace manufacturers, being just as tightly regulated as medical device manufacturers, already know the many advantages that Computer Aided Inspection (CAI) can provide in their ongoing efforts to build better engines and airfoils at a faster turnaround.
 
We’ve narrowed the many advantages of CAI to six broad categories of greatest interest to medical device manufacturers.
 
Advantage: Benefit:
Secure and Archiveable CAI tools save comprehensive surface data instantly. You can keep your measurement data for decades, ensuring a lasting command of your company’s legacy intellectual property for future revisions or study. This also simplifies the process of ensuring compliance with the strict and changing archive requirements imposed by many countries.
Auditable for regulatory inquiries Given correct information technology practice, CAI data are immune from tampering. When secured in a database that cannot be changed once logged, you have incontrovertible evidence of a watertight quality system when FDA inspectors knock on your door. If necessary, CAI can allow you to prove that every surface point of your product was within spec at every point during manufacture.
Traceable for staff accountability Gauge R&R studies demonstrate that CAI incorporates no operator-dependent error. All manufacturing and quality personnel can be held accountable for their respective step in recording engineering data. Every step in manufacturing is linked to a comprehensive dimensional inspection process, and no measurements are taken by anonymous users.
Trackable for failure analysis CAI allows manufacturers to track inspection data through the process to find the root causes of failures systematically, rather than by trial and error. Intelligent surface data analysis provides quick and effective tracking from why-gate through why-gate. There is no longer any need (or excuse) for multiple iterations.
SPC Trendable CAI data are immediately and continuously transferable into statistical process control (SPC) frameworks. By trending dimensional changes, manufacturers can catch emerging anomalies before they grow into costly problems. And by driving these new insights upstream into design, prototyping, and tooling, manufacturers can improve their understanding of tool and machine wear, reducing the frequency of planned shutdowns.
Admissible in litigation High-profile court cases (based on questionable premises) have proliferated against the industry in recent years. With Computer Aided Inspection (CAI) data, manufacturers now have a powerful defensive tool in depositions or the courtroom. CAI provides incontrovertible evidence that every surface point of your part was within spec, when questioned by plaintiffs’ attorneys.

Over the next several months, we’ll be sending a series of informational messages to elaborate on these advantages to help our medical device friends and partners move forward into comprehensive integration of CAI into their processes and workflow.

Visit www.level3inspection.com or call us today to learn more!

WARSAW, IN • STUART, FL
574.383.9145 • 561.775.7911
Copyright © 2011 Level 3 Inspection LLC, All rights reserved.
MENU